How to repair a fiberglass tub or shower

A crack in a fiberglass tub or shower isn’t always a reason to replace it.

Fiberglass repair — once left to the professionals — can now be completed by the meticulous homeowner using a fiberglass repair kit.

How to repair a fiberglass tub or shower

Before attempting a repair, it is important to know that most likely the crack will still be slightly visible.

If this bothers you, have your fiberglass tub or shower replaced, or call a professional to make the repair. However, if you just want to make a repair that will enable you to continue to use your shower, then you can fix it yourself.

Here are step-by-step instructions to assist you with your fiberglass tub repair project…

Why Did The Fiberglass Crack?

The first step in making a repair is to figure out why the crack occurred and fix the underlying problem.

If you dropped something in the shower and caused the crack, no further repair is needed. However, if the crack in the fiberglass started to appear over the course of several days, you must provide additional support to prevent more cracks.

  • Drill a hole through the crack and into the cavity below.
  • Fill the cavity with an expanding foam sealant

How To Repair A Fiberglass Tub/Shower

  • To make a fiberglass repair, you’ll need a fiberglass repair kit and epoxy paint that matches the fiberglass. You’ll also need an attachment for your drill that will allow you to sand the area surrounding the crack. And make sure that the area you will be working on is completely dry before beginning any repair.
  • Using the drill attachment, sand the area around the crack until you hit well-bounded fiberglass that is in good condition. Then, using the materials from your fiberglass repair kit, cut dry fiberglass patches to fit the hole in your shower. (Because fiberglass is formed out of several thin layers, you will need several fiberglass patches to make the repair.)
  • Mix the epoxy and resin contained in the kit. Dip each piece in the mixture and smooth it into place, layering each patch over the patch before it. The last patch should be level with the rest of the tub. (Most fiberglass tub repairs require only 3 to 4 layers.)
  • Wait for the fiberglass repair to harden according to the kit directions. Since fiberglass is not waterproof, you must use a fiberglass sealant over the patch (normally included in the kit) to prevent any leaking. Wait for the whole area to cure.

How To Check Your Work

Next, do a test for leaks.

How to repair a fiberglass tub or shower

  • Fill the bathtub with water and mark the level of the water with a piece of tape.
  • Come back in 4 to 6 hours to make sure that no leaks have occurred.

If your repair doesn’t leak, you should now paint the entire shower or tub with epoxy paint. This will blend the patch with the surrounding area and create an additional seal to prevent any future leaks.

Epoxy paint is difficult to work with. Be sure to work slowly to prevent any streaking and to create the best looking finish possible.

I have a lot of hands-on experience in the home construction industry, with a good deal of experience in sustainable building. I’m mostly interested in home restoration and home renovations.

The answer is yes! Refinishing is a great method for repairing fiberglass and making it like new. After only a few years, many fiberglass tubs, showers and shower/tub units can become dull and even worse, they can develop cracks and holes that cause water leaks.

How to repair a fiberglass tub or showerOn the bright side, Miracle Method can repair those stress and structure cracks, and make your bathtub or shower more beautiful than the day it was installed. We use only the most advanced resins and fiberglass tub refinishing materials to repair unsightly cracks, holes and damage. We can even restore or change the color of your fixture to your utmost satisfaction. We offer a variety of colors and textures including our Natural Accent stone-look finishes.

Another important thing to know about fiberglass refinishing is that most one-piece shower/tub units are built into the structural framing of the walls. This makes removing them very labor-intensive and costly. Miracle Method refinishing does not remove the fixture but rather refinishes it right in-place saving you as much as 75 percent compared to the cost of removal and replacement.

To learn more about refinishing, visit our Miracle Method Consumer Guide or call 855-212-7337.

This article was co-authored by our trained team of editors and researchers who validated it for accuracy and comprehensiveness. wikiHow’s Content Management Team carefully monitors the work from our editorial staff to ensure that each article is backed by trusted research and meets our high quality standards.

wikiHow marks an article as reader-approved once it receives enough positive feedback. This article received 11 testimonials and 94% of readers who voted found it helpful, earning it our reader-approved status.

This article has been viewed 903,783 times.

Fiberglass showers and bathtubs are durable, easily maintained, and attractive fixtures, but they may still be accidentally damaged. Fortunately for homeowners, there are inexpensive kits available that can be used to make repairs if this happens.

How to repair a fiberglass tub or shower

  • Make sure your shower is fiberglass by tapping it with your knuckle or a wooden spoon or similar item which will not damage the finish. A fiberglass unit will have a soft, hollow, non-metallic sound, and depending on where you tap it, may even seem flexible.
  • Choose the appropriate color for the kit you will purchase. Most kits come with colorants (tinting products) to change the color of the product to match common colored fixtures, such as white, off white, or almond.
  • Make sure the kit you buy comes complete with everything you need, or purchase these materials and tools separately. The following is a list of what your kit may contain:
    • Polyester resin
    • Hardener (catalyst to harden the resin)
    • Fiberglass mesh or mat (for large or structural repairs)
    • Colorants
    • Sandpaper in assorted grits, from 80 grit (coarse) to 400 or 440 grit (very fine)
    • Thickener (to stiffen the resin for vertical applications)
    • Protective gloves resistant to the chemicals included in the kit
    • A mixing container and stirring tool

    Could your fiberglass tub or shower use a little TLC? Fiberglass repair isn’t for everyone, but it can be a DIY project if you’re familiar with bathtub refinishing. To try fiberglass repair yourself, use the following step-by-step guide.

    1. Get your kit

    For bathtub refinishing, you will need a fiberglass repair kit. Verify that your bathtub is actually fiberglass before you proceed. If you tap on it with a wooden spoon or your knuckle, it should make a hollow, non-metallic noise.

    Fiberglass repair kits come in a variety of colors, so choose the color that matches your existing tub. If you need to alter the color slightly, most kits come with tinting products that allow you to do so. Your kit should also contain hardener, a fiberglass mesh or mat, polyester resin, sandpaper, protective gloves, thickener, a mixing container and a stirring tool.

    2. Clean thoroughly

    Before you complete your fiberglass repair, you must clean the area that requires the repair. Remove any jagged fibers from the area. Sand it to remove any contaminants. Then, rinse it with solvent to prepare the area for the repair product. The area must be very clean and smooth for proper adhesion.

    3. Reinforce with fiberglass cloth (if needed)

    If the area that needs repair is more than one quarter-inch wide or is an open hole, you will need to use fiberglass cloth reinforcing. Cut a piece of cloth that is slightly larger than the area that needs repair. If the area is particularly large, you may need to use more than one layer of fiberglass cloth.

    4. Read the instructions

    Review the kit instructions for mixing and tinting the materials before you proceed. Each product varies slightly, so be sure to have a good understanding of how to properly mix and tint before you proceed.

    5. Mix (don’t forget to protect your floor!)

    Use cardboard or heavy construction paper to protect the surface where you will mix your fiberglass repair material. Measure the recommended amount of resin and mix it according to the kit guidelines. Don’t forget to include any colorant that is recommended to make the mixture the right tint for your bathtub.

    6. Thicken and harden

    Again, following the kit instructions, add the thickening and hardening agents to the mixture.

    7. Mix again, quickly

    Remember, the longer you stir, the better results you’ll get. However, once you add the hardener, you’ll only have up to 15 minutes of working time.

    8. Apply the mixture

    Use a putty knife or other flat tool to apply the mixture to the damaged surface. Spread evenly, making it slightly thicker than the original surface to allow for sanding to finish.

    9. Dry

    Allow the material to harden. This typically requires about two hours.

    10. Sand and buff

    Use coarse sandpaper to smooth the repaired area. Work your way from coarse to smooth paper as you sand, until the area is even with the rest of the bathtub surface. Your kit should include a buffing compound that you can use to buff the area and give it a gloss finish to match the rest of the surface.

    Call for backup

    To skip all of these steps and let the experts handle your fiberglass repair, contact the pros at A-1 Porcelain & Fiberglass Service Co., LLC. We specialize in bathtub refinishing. Call us today for all of your bathroom repair and refinishing needs.

    How to repair a fiberglass tub or shower

    Fiberglass showers and bathtubs are a regular fixture in many homes because they’re easy to maintain, durable, and attractive. But despite their durability, they may still get accidentally damaged or cracked.

    Instead of replacing the whole thing, consider fixing it.

    How easy is it to repair a cracked fiberglass tub or shower?

    Fortunately, there are affordable and easy-to-find kits available for homeowners that can make the task of repairing a cracked fiberglass tub or shower a breeze.

    This article includes all the steps to help you with the task. So keep reading.

    Your Step-by-Step Guide to Repairing a Cracked Fiberglass Tub or Shower

    Here’s everything you need to know for repairing a cracked fiberglass tub or shower successfully.

    Get the Right Kit

    First, you need to be sure that your bathtub or shower is made from fiberglass. When buying a suitable kit, make sure you get the right color according to your bathtub or shower. Most kits come with tinting products – also called colorants – so you can mix and change the color according to your fixture, ordinarily white, off white, or almond.

    Also, check to see if your kit includes everything you will need. Here are the things it should contain:

    • Hardener (catalyst for hardening the resin)
    • Polyester resin
    • Colorants
    • Fiberglass mat or mesh (required for structural or large repairs)
    • Sandpaper in assorted grits (coarse or fine)
    • Thickener (used for thickening the resin during vertical applications)
    • Protective gloves resistant to all the chemicals used in the process
    • A container to mix with a stirring tool

    Inspect and Clean the Repair Area

    Inspect the area that needs to be repaid and remove any protruding or jagged glass fibers. Use fine-grit sandpaper to sand it slightly to remove oil, wax, soap scum, or other contaminants. Also, use some solvent like acetone to clean the area before applying the repair product.

    Consider Fiberglass Cloth Reinforcement

    While you’re inspecting the damaged area, you should determine if it needs fiberglass cloth reinforcement. If not, skip to the next step. If the crack is large and wide, filling it with the resin mixture will not fix it. You must use the fiberglass cloth or mesh to fill in the hole or cracks before fixing in the product.

    Mixing and Tinting

    You should always read the instructions on the package for mixing and tinting. Follow the measuring of mixtures following these instructions for the best results.

    Place the mixing container on a construction paper or cardboard before mixing the material. Following the measurement guidelines, pour the polyester resin into the mixing container and mix it with an appropriate portion of hardener.

    Add the Colorant

    Now add in the colorant that comes with the kit to match your fixtures. Mix all the components thoroughly, and before applying, check the color against the bathtub or shower to see if it matches perfectly. Do this step before adding the hardener.

    Add Hardener

    Next up, add the hardener following the instructions on the kit. Adding the right amount of hardener will accelerate the process and reduce the working time. On the other hand, if you add too little, it will increase the setting time. As a ball-park estimate, five drops of hardener usually works for one tablespoon of resin and colorant mixture.

    Mix in the Repair Material

    Once everything is in the mixing container, whisk thoroughly to combine everything well. Do this step quickly, because after adding the hardener you will have 10-15 minutes before the resin will start to solidify. You need to start working before the mixture becomes too hard to use.

    Application Guidelines

    To apply the mixture, use a wooden tongue depressor or a putty knife-like tool to scoop it out of the container and place it on the cracked area. If you’re using fiberglass cloth, place the piece over the damage and press it into the resin mixture.

    Start spreading the mixture and even it out. Keep the level slightly higher than the surrounding surface because you will sand it down to a final finish. After applying the material, leave it for at least 2 hours at room temperature to allow it to cure.

    Once cured, sand the filling without scuffing the surrounding. If the fiber needs trimming, do that now and use sandpaper to finish the patch. Continue until the repair looks smooth again.

    Overlay the First Patch

    The last step is to overlay the initial repairs. Mix another batch of resin and colorant without any hardener. Apply this on the patch with a paintbrush or a cotton swab. Smooth out the application and let it harden using very fine sandpaper.

    How to repair a fiberglass tub or shower

    Fiberglass or acrylic bathtubs and showers are easy to install and are often less expensive than other options, such as a cast-iron tub or ceramic tile shower stall, making them a favorite for budget-conscious homeowners. Over time, though, the acrylic or fiberglass surfaces can get dented or cracked, often because of flexing of the walls of the fixture over time. Sharp blows can also dent, crack, or punch holes in fiberglass or acrylic. A variety of options are available at this point, including wholesale replacement of the bathtub or shower, or installing a new liner inside the old tub or shower.

    But one fix that is much more cost-effective is to fill the crack or hole using a fiberglass/acrylic repair kit. These materials include epoxy-like materials similar to the compounds used as filler in automobile body repairs. In fact, some people use these automotive body fillers to make repairs on tubs and showers, or even sinks and toilets.

    Acrylic/Fiberglass Repair Kits

    Rather than using automotive body filler, though, a better choice is to buy a repair kit that is factory-matched to your tub or shower. These kits have filler paste already tinted to match the color of your fixture, and will include much of what you need to make the repairs—only a few extra tools and materials are required. A single kit may provide enough material to make several repairs. One manufacturer of fiberglass/acrylic repair kits (but not the only one) is Multitech Products, who makes many of the official repair kits sold by the plumbing fixture manufacturers themselves.

    There are many repair and resurfacing products available, so make your choice carefully. For simple cosmetic repairs, most people find that a paste-type fiberglass/acrylic kit is easier to use than a spray product. Paste kits may include:

    • Base coat paste and catalyst
    • Lightening and darkening toners
    • Rubbing compound or buffing bar
    • Wet/dry sandpapers

    Some types of products also include a clear top coat that is sprayed or brushed on.

    You Will Need

    • Acrylic/fiberglass paste-type repair kit, color-matched to your fixture
    • Utility knife
    • Power drill with small drum sander or grinding disks
    • Wet/dry sandpapers (220-, 320-, 400-, and 600-grit)
    • Nail polish remover or acetate
    • Clean cloths or paper towels
    • Heat gun
    • Buffing bonnet
    • Protective gloves
    • Ventilator mask

    Warning

    This repair uses an epoxy-type filler that has hazardous fumes.   Good ventilation is required, as well as the use of an approved ventilator mask. Always follow the kit manufacturer's recommendations for safety measures.

    How to Use a Paste-Type Acrylic/Fiberglass Repair Kit

    1. Use a sharp utility knife to carve out a V shape around the edges of the damaged area. Make sure to cut down through the color layer of the acrylic or fiberglass into the structure below. Usually, this means cutting down between 1/16 and 1/4 inch. If the surface is very hard or the damaged area is very large, a sanding drum or grinding disk attached to a drill or Dremel tool will make this preparation easier. Angle the sides of the damaged area so that the filler paste can be applied smoothly.
    2. Wipe the surfaces clean with cloths or paper towels, then use 220-grit sandpaper to slightly roughen the entire repair area. This slight roughening will help the paste adhere to the damage area.
    3. Clean the repair area with nail polish remover or acetate. At this point, make sure to ventilate the area well and use a ventilator mask. Wear protective gloves for the following steps.
    4. Transfer a small amount of paste filler from the kit into one of the provided mixing cups. If necessary, use the lightening or darkening toners to adjust the color to match your tub or shower (this is most often necessary with white tubs or showers).
    5. Add the catalyst agent to the paste in the ratio recommended by the manufacturer. Mix the ingredients together thoroughly to form the activated filler paste.
    6. Apply the activated paste mixture to the repair area using the mixing stick provided in the kit. Make sure to fully fill the damaged area. Overfill the patch area slightly; it will be sanded flush later.
    7. Allow the paste to fully harden for one hour, or according to the kit instructions. A heat gun can be used to speed up this drying time.
    8. Use wet/dry sandpaper to blend in the repair area with the surrounding surface. The best results are achieved if you sand in several stages using progressively finer grits of wet/dry sandpaper. Begin with 220-grit, then proceed by sanding with 320-, 400-, and finally 600-grit sandpaper. As you sand, drip water onto the sanding area with a wet rag to lubricate the surfaces.
    9. Clean away the sanding dust, then use the rubbing compound included in the kit to polish and blend the repair area with the surrounding material. High-speed buffing will give the best results—a buffing bonnet mounted to a drill or an automotive buffing tool is a good choice.
    10. If your kit includes a clear top-coat layer, apply it now, according to kit instructions.

    Done patiently and according to instructions, the repair to your fiberglass or acrylic tub or shower should be nearly impossible to distinguish from the rest of the fixture.

    The cost associated with replacing a fiberglass bathtub or enclosure can end up being very expensive. If your fiberglass bathtub has been damaged by cracking, chips or discolorations, professional bathtub repair or our do-it-yourself refinishing products are the answer to your problem.

    Even large fiberglass bathtub cracks, measuring up to ten inches can be repaired in just a couple of hours. The process includes supporting, and strengthening the damaged fiberglass under the crack. Most fiberglass cracks are caused by poor support underneath your bathtub. Supporting the bottom of the bathtub is vital. Easy step by step directions are included in our do-it-yourself fiberglass repair kits.

    Most fiberglass damage is easy to repair once the area is cleaned of loose debris and jagged edges are smoothed with the use of a Dremel Tool. This amazing tool is used by most professional bathtub refinishers. If you don’t have this tool, a file can be used. Next, the fiberglass under the repair area is given extra support. This process is easily performed following the directions in our repair kit

    Fiberglass Shower Pan Stained and Hard To Clean?

    Try our fiberglass surface restore kit. This kit works great on hard to clean shower floors. Contains two strong surface cleaners that remove stains and water deposits from fiberglass shower pans. Also includes a polymer finish coating that restores the luster and seals your fiberglass pan to help resist future staining and water spots. No other cleaners can match this system.

    If using a professional to refinish your fiberglass fixture, the cost for such a fiberglass repair will depend on the extent of the damage to your bathtub or shower surround. Our you can save hundreds of dollars doing it yourself

    Rigid Fiberglass Bathtub Repair Inlay Kit

    Repair major damaged to fiberglass bathtub floor bottoms in an hour or less. Restore your bathtub bottom holes, repair cracks or fiberglass tubs needing extra support. Our fiberglass tub inlay kits are almost invisible once installed, have a non slip surface and you will save over $1000 versus replacement.

    We have a fiberglass tub, and 7 years ago when we moved into our brand new house with brand new tub, there was a chip or crack in a couple places of the tub, so the builder “fixed” those spots, but really they ended up looking worse, and have seriously yellowed over the years. What should we have done instead of letting him “sand down” the cracks? They were like hairline scratches, rather than deep cracks, but his “repair” actually made it worse. Perhaps your advice will help others before they go the route we did. — L.G.

    How to repair a fiberglass tub or shower

    Following are some tips for fixing fiberglass tub scratches…

    Uh Oh, The Fiberglass Is Scratched!

    Cracks and scratches in fiberglass tubs are not unusual.

    We’ve all seen home remodeling shows on TV.

    With all the dirt, confusion, and transportation in & out of materials, the possibility that something will get dropped, bumped into, or scraped against your shiny new fiberglass bathtub is a real concern.

    This is made worse by the fact that usually the one-piece tub unit must be installed first — before the drywall, before the flooring, and before all the plumbing fixtures. All it takes is one small slip and you’ve got a gouge requiring some serious fiberglass tub repair.

    Fortunately, if done properly a fiberglass repair can look as good as new and should provide many years of trouble-free service.

    How To Do Fiberglass Tub Repairs

    Keep in mind that a fiberglass tub isn’t an old piece of lawn furniture that can be fixed with a can of Rustoleum spray paint.

    For a fiberglass tub repair to last (and blend in properly), you must use materials designed specifically for repairing fiberglass.

    When fiberglass products are molded, the color of the item is mixed with the gel coat. This means when it comes out of the mold, the final exterior finish was the first layer placed in the mold.

    No paint is applied. Frankly, paint won’t hold up to the environment that your fiberglass tub will be placed in.

    Any repair that amounts to sanding down the scratch or gouge, and spraying paint over the damage will not last. It may look presentable for awhile, but chlorine cleansers will fade or discolor the fiberglass repair, and in no time it will look worse than the original damage.

    A proper fiberglass repair requires the use of a fiberglass tub repair kit containing fillers designed specifically for the task.

    The key to success is the fact that the acrylic color will be mixed into the filler, not applied on top of the repair.

    More severe damage that might happen over time — such as cracks that go all the way through the tub or even holes — can all be repaired. Fiberglass is a very versatile product that is much easier to repair than most other building products.

    Fiberglass mats can also be applied under the bottom of a damaged tub floor to reinforce an area that wasn’t properly supported.

    Totally refinishing an aged bathtub can return it to like-new condition. Maybe you’re a bit tired of the pink colored tub that’s been in your home for ages. Updating the color with a new gel coat infused with a more current pigment will make your bathtub look like new.

    Here’s a video that shows the entire bathtub refinishing process:

    So, when that first scratch on your fiberglass tub happens (and just like with a new car, it always does) don’t break out the sledge hammer and start demolition.

    Consider repairing or refinishing your fiberglass tub. It’s a whole lot cheaper than remodeling!

    I’ve been involved in RVing for 50 years now — including camping, building, repairing, and even selling RVs. I’ve owned, used, and repaired almost every class and style of RV ever made. I do all of my own repair work. My other interests include cooking, living with an aging dog, and dealing with diabetic issues. If you can combine a grease monkey with a computer geek, throw in a touch of information nut and organization freak, combined with a little bit of storyteller, you’ve got a good idea of who I am.

    I will admit in the past I have paid over $1,500 to get a tub surround replaced which could have been fixed with this solution. Since then I have learned a few things and one of those things is how to repair holes in a fiberglass surround ensuring a watertight surface and something that isn’t an eyesore.

    For this project, I used Devcon Fiberglass, Porcelain, and Plastic Repair Kit, which was about a $13 investment, plus a few other tools I already had in my garage (see below). While the process is fairly easy, it does take a little patience when it comes to sanding the surface for a smooth finish.

    Note: You can also use the epoxy on cracks and other small knicks in your tub surrounds – it’s not just for screw holes.

    If you’d rather watch than read, check out the YouTube video below.👇

    Tools:

      ** this works on fiberglass, porcelain, and plastic
    • 1-gallon ziplock bag (cut it into square sheets)
    • Toothpicks

    DISCLAIMER: This blog contains affiliate links, which means that if you click on one of the product links, I’ll receive a small commission.

    How to Patch and Filling Screw Holes in a Fiberglass Bathtub – 7 Steps

    For this example, I was patching screw holes left behind after I removed a glass shower door from my tub/shower surround. Overall I had a total of 6 holes to fill and I ordered 2 kits and did 1 side (3 holes) at a time. This Playlist shows the whole project on our YouTube Channel.

    1. Section Off Area with Painter’s Tape

    How to repair a fiberglass tub or shower

    Securing Area with Painter’s Tape

    Before you do anything with the epoxy kit, prep the surface by sectioning off the holes with painter’s tape. I like to make a box shape around each hole. This will contain the epoxy when it runs and it will help later on when you start sanding the area. Also, ensure the surface has no loose pieces and is completely clean of any oils or residue.

    2. Squeeze & Mix the Epoxy

    How to repair a fiberglass tub or showerSqueezing the epoxy mixture

    With the Devcon Repair Kit, press the epoxy from the bottom of the packet. Continue to mix it with your hands for about 45 seconds to ensure you have a complete mix. (I then added the almond color to the epoxy since my bathtub is almond-colored.)

    Warning: You only have about 5 minutes of working time before the epoxy starts to firm up so make sure you have everything ready once you get to this step.

    3. Fill in Screw Holes with Epoxy

    How to repair a fiberglass tub or shower

    Filling in screw holes with epoxy

    Using the toothpick, place the epoxy directly in the screw holes. It’s ok if it drips out a little. You’ll be adding more epoxy in the next step. Since my holes were small I only used epoxy if you have a larger hole and need additional strength the kit will come with some fiber mesh to cover the larger hole and provide the additional strength once dry.

    4. Brush Extra Epoxy on Holes

    How to repair a fiberglass tub or shower

    Brushing extra epoxy on the holes

    Brush and spread out the epoxy. Be sure to build it up so you have a little extra. Don’t worry, I know it looks gunky! You’ll use the ziplock plastic sheets to smooth it out in the next step.

    5. Place Plastic on the Epoxy and Tap Over Them

    How to repair a fiberglass tub or shower

    Tapping out air bubbles over the screw holes

    Place the plastic sheet over the holes filled with epoxy. Then, tap over the area to get the air bubbles out and smooth out the surface. Don’t worry once everything is dry (I let it sit for 2-3 hours) the ziplock bad will come right off without any issue.

    6. Sandpaper Over the Holes

    How to repair a fiberglass tub or shower

    Using 60 grit sandpaper over the holes

    Remove the plastic sheet and sand over the epoxy with 60 grit sandpaper. This is the roughest sandpaper I used and is meant to quickly remove the excess epoxy. Do not sand the surface of your tub surround with this sandpaper or it will remove the finish.

    7. Peel Tape Off & Sandpaper Again

    How to repair a fiberglass tub or showerThis is what the area will look like when the tape is off

    Peel the painter’s tape off and go back over the epoxy with more sandpaper. Switch to 320 grit sandpaper and continue to sand. Finally, switch again to 600 grit and continue to sand until smooth.

    Pro tip: Add a little water to the surface as you’re sanding for the smoothest finish.

    The Wrap Up

    How to repair a fiberglass tub or shower

    The finished result: a look at the smooth surface after the area is patched up and sanded

    Overall, I was pleasantly surprised with the Devcon Epoxy Bathtub Repair Kit. The almond finish matched surprisingly well and I was happy with the flush finish. I also ended up putting a curtain rod up, which made the patched-up holes barely noticeable. But let me know what you think. If you’ve tried this project, feel free to share what worked for you in the comments below… or let me know what you’d do differently.

    Watch more videos of home repair projects at the Everyday Home Repairs Youtube Channel.

    Home Owner, Real Estate Investor, and Creator (YouTube). Here to help others save time and money through doing their own home repairs and improvements.

    Recent Posts

    If you’re here, you’re probably in a pinch to get your garage door open. I know the feeling! Especially when I’m in a hurry to get my kid to school or head to work – this can be a really.

    Is your bathroom sink drain stopper not working effectively? You’re in the right place! In this blog, you’ll learn how to maintain or fix your lift rod and the associated drain stopper. It’s.